Box Stall Drinker

For corner installations in box stalls, but can be installed outdoors as well.

Features

Stainless steel access plate. Half moon design on back corner for securing up to a 2 inch (5.1 cm) PVC tube for plumbing from above or below.

Foam filled-R value of 7.5 inch.

Internal 3/4" (1.9 cm) AND external 2" (5.1 cm) drains; drinker is very easy to clean. No disassembly for cleaning required.

Antisiphon fill valve delivers about 2 1/2 gallons (9.5 liters) per minute; simple water level adjustment, easy to clean.

Optional heater, 250 watts, 110 volts. We tested this unit in a cold chamber at minus 30 degrees Fahrenheit (-34.4 degrees C). No freezing occurred at this temperature-even after 7 days!

Available in Blue or Red.

Ground Mounting Tube

Optional Ground Mounting Tube

For hookup to underground service connections and for outdoor installations.

Poly Drinker

Water horses, calves, wildlife with Performance One model MPO6, for stalls, corrals and paddocks.

Features

Antisiphon fill valve delivers about 2 1/2 gallons (9.5 liters) per minute; simple water level adjustment, easy to clean.

Double wall, single piece poly construction--ALL SMOOTH.

Foam filled insulation--R value of 7.5 per inch which offers lots of freeze protection.

Optional heater, 250 watts, 110 volts. We tested this unit in a cold chamber at minus 30 degrees Fahrenheit (-34.4 degrees C). No freezing occurred at this temperature--even after 7 days! Heating cost is minimal--less than $10.00 per heating season.

Four recessed anchor notches for secure installation.

Easy access to valve and heater -- just lift stainless steel access plate.

Drinker is very easy to clean--no disassembly for cleaning required.

Large 2” External AND Internal (5.1 cm) clean out drains.

Cavity for warm climate installations only. Some warm geographic areas do not use a riser tile and may only have a buried supply line protruding through a concrete pad. The cavity can be used to make the connection from the supply line to our valve.

Model MPO17

We’ve been watering animals since 1903!

Poly Drinker

Performance One E-Drink

Electrically Heated *Energy Efficient.

You Only Need One Unit To Water Up To 150 Head Of Most Any Species.

A typical winter heating bill — $10.00 or less! Why? Two reasons. Our drinker has 17 gallons of capacity. Incoming water carries heat energy. The more water, the more heat. Our R-valve of 7.5 per inch holds the heat provided by incoming water. Secondly, our supply line is in the water. You don’t need extra heat to keep the line above the ground open. You do need proper installation to prevent the supply line underneath the drinker from freezing.

Features

2 large drink openings 8” x 14” each. Drinker wells are 14” deep allowing most any animal to drink naturally.

100% poly construction. Molded with the most effective ultraviolet inhibitor. Tough enough for years of outdoor use.

Notched flanges for easy anchoring.

Over 300 square inches of access for easy hook up.

Stainless steel spring loaded valve cover removes easily. No loose parts to lose.

2-2 inch side drains and 1 threaded bottom port for optional inside drain.

Sealed bottom keeps out moisture and rodents.

Dependable nonsiphoning Durapride valve.

Proven (15 years of use) 250 watt heater.

Poly Drinker

New!

Similar to Model MPO17 but with an access door.

Features

Spring loaded pin allows access panel to pop off with the twist of a screwdriver. There are no loose parts.

Recessed, protected notches for secure anchoring.

Two inch built-in drain.

Proven (20 years of use) 250 watt heater.

Stainless steel spring loaded attachment pins make cover removal and replacement easy. Again,there are no loose parts.

Overflow port.

Dependable non-siphoning Durapride valve.

Brower

Our broad line-up of models all sport superior quality. Drawn galvanized steel troughs and galvanized steel jackets are standard. Handy plugs drain water in seconds. All models are super insulated and fully warranted.

SUPER INSULATION CUTS HEATING COSTS. Extra thick foam insulation has an R-value of 7.14 per inch - the most of any competing waterers. Our polyurethane foam clings tightly around the trough and on the jacket. This superior insulation is water resistant, is unattractive to rodents, and contains no formaldehyde or chlorofluorocarbons. Cuts your heating costs.

RUGGED VALVE WON’T CLOG OR RUST All models feature our exceptionally dependable rugged valve constructed of ABS, a tough and low porosity material.

Hogs Steel Drinker

Waters up to 150 hogs. Install in a fence line to serve two pens. Rugged lids keep dirt out and save heat in winter. Mud grates keep water clean and sanitary.

Horses, Calves and Wildlife Steel Drinker

Our most popular unit has lots of versatility. This unit is 18" high to water 25 horses, 40 ponies, 100 calves, 40 head of cattle, or small groups of wildlife. Heavy gauge sidewalls and drawn steel troughs are rounded to prevent livestock injury.

Horses, Calves and Wildlife Steel Drinker

A single trough version of Model MK32.

Cattle Steel Drinker

Serves 125 head of cattle or 70 horses. Suitable for range, pasture or feedlot use. Painted, galvanized steel jacket with formed galvanized steel trough and cast iron valve cover.